真空干燥機的調試方法有哪些?

1、在調試前我們需要將箱門關上還要將門的拉手旋緊到位，然后關閉放氣閥，并開啟真空閥。當然在^一使用時可能真空閥的開關比較緊，你可以用力旋轉。

1. Before commissioning, we need to close the box door, tighten the handle of the door in place, then close the vent valve and open the vacuum valve. Of course, when you use it, the vacuum valve may be tight. You can rotate it with force.

我們?cè)诮油ㄕ婵毡秒娫磿r(shí)，需要開始抽氣，此時則需要先關閉真空閥后再關閉真空泵電源，好防止真空泵機的油倒流到工作室內，此時真空干燥機內是處于真空狀態。此為抽真空調試法。

When we connect the power supply of the vacuum pump, we need to start pumping. At this time, we need to close the vacuum valve first and then turn off the power supply of the vacuum pump, so as to prevent the oil of the vacuum pump from flowing back into the working room. At this time, the vacuum dryer is in a vacuum state. This is the test method of true air conditioning.

2、要打開真空干燥機的電源，那么這時其電源燈亮起并進行自檢，那么這時也就表示已進入狀態了。要進行真空干燥機的溫度設置了，這一步很重要，所以想在下面花一個單獨的文章來做一下，當機內的溫度設定到接近指定的溫度時，那么加熱就開始進入到PID調節階段，那么這時儀表就會有時測量溫度超過設定溫度，伸也有時低于設定溫度屬正?，F(xiàn)象。

2. First of all, turn on the power of the vacuum dryer, then the power light will be on and self-test will be carried out, then it means that it has entered the state. To set the temperature of the vacuum dryer, this step is very important, so I want to spend a separate article to do it. When the temperature in the machine is set close to the specified temperature, then the heating begins to enter the PID regulation stage. At this time, the instrument will sometimes measure the temperature higher than the set temperature, and sometimes lower than the set temperature, which is a normal phenomenon.

那么當測量溫度時如果已經接近或者是等于設定溫度后，再過1到2小時后就差不多能夠進入恒溫狀態了。如果說所需溫度比較低的時候，我們可以采用二次設定的方式，好使它能夠盡快進入到恒溫狀態。

When measuring the temperature, if it is close to or equal to the set temperature, it will almost enter the constant temperature state after 1 to 2 hours. If the required temperature is relatively low, we can use the method of secondary setting, so that it can enter the constant temperature state as soon as possible.