制氮機次開機應該注意哪些問題？

制氮機大家都是比較熟悉，是以空氣為原材料把空氣中的氮?dú)夂脱鯕膺M(jìn)行分離的一種制氮設備，很多人都會對制氮設備進行操作。然而很多人往往因?yàn)樘煜ち司蜁?huì)忽視制氮設備的次開機這個因素，下面山東制氮機的小編就來給廣大用戶簡單的介紹下制氮設備次開機應該要注意什么，下面就一起來看看吧。

Everyone is familiar with the nitrogen generator. It is a kind of nitrogen making equipment which uses air as raw material to separate nitrogen and oxygen in the air. Many people will operate the nitrogen making equipment. However, many people tend to ignore the factor of the first start-up of nitrogen generation equipment because they are too familiar with it. The following editor of Shandong nitrogen generator will give a brief introduction to what should be paid attention to when the nitrogen generating equipment is started for the first time. Let's have a look at it.

先查看體系閥門（開。關）的方位，空壓機出口節門常開，制氮機進口節門關增壓機進出水節門均關，氮?dú)鈨?chǔ)罐進時令門關。體系通電 3.先接通制氮機，等外表呈現數值后，把溫度表上的溫度值設定到40℃純度表上的純度值設定到0.6。

First check the system valve (on. The outlet throttle valve of the air compressor is normally open, the inlet throttle valve of the nitrogen generator is closed, the inlet and outlet water throttle valves of the booster are all closed, and the valve is closed when the nitrogen storage tank enters. Turn on the nitrogen generator first, and set the temperature value on the thermometer to 40 ℃ and the purity value on the purity meter to 0.6.

開冷干機，并使其作業1—2分鐘，一起看一看蒸發表不能為零。開空壓機，使空氣罐罐內壓力在1、1MPa以上時，翻開制氮機進口節門。把制氮機的采樣流量計調到1.5擺布。 7.把增壓機進水節門翻開，并把添加機兩個上節門翻開，使水柱在50mm擺布，并關上節門，翻開排水閥，再翻開氮?dú)鈨?chǔ)罐進時令門。

Turn on the cold dryer and let it work for 1-2 minutes. Let's have a look at the evaporation meter, which can't be zero. Open the air compressor to open the inlet throttle of nitrogen generator when the pressure in the air tank is above 1 and 1MPa. Adjust the sampling flowmeter of nitrogen generator to 1.5 pendulum. 7. Open the water inlet throttle of the booster and the two upper throttle valves of the adding machine to make the water column swing at 50 mm. Close the throttle valve, open the drain valve, and open the timing valve of the nitrogen storage tank.

當?shù)獨鈾C(jī)上的氮?dú)鉄袅習r，（純度上的實踐值低于設定值），敞開增壓機。當增壓機把氮?dú)鈨?chǔ)罐打滿后，增壓機自停，再把制氮機上溫度表的溫度設定到0℃時，符溫度表實踐溫度降低30℃以下，（夏天到室溫），將制氮機進口節門封閉。

When the nitrogen lamp on the nitrogen machine is on (the actual value of purity is lower than the set value), open the booster. When the supercharger fills up the nitrogen storage tank, the supercharger stops automatically, and then sets the temperature of the thermometer on the nitrogen generator to 0 ℃, the actual temperature of the thermometer is reduced below 30 ℃ (from summer to room temperature), and the inlet throttle of the nitrogen generator is closed.